Spread the load. Square to the wood.

Hot-dip galvanized square plate washers for 1/2" to 1" bolts. 2" x 2" up to 6" x 6", 1/8" to 1/2" thick, plus a curved washer for round posts.

Shop galvanized square washersSize chart ↓
★Fastener specialists since 1977
✓Order by noon EST, ships same day
$Free shipping over $100*
%Volume discounts up to 25%

Galvanized Square Washers

Shop by bolt size

4 bolt sizes, 15 washers

Pick your bolt diameter, then the plate size and thickness.

Hot-dip galvanized square plate washer, The Nutty Company
Why square washers

Made to hold in wood

01

Big bearing surface

The wide, flat plate spreads the load of the nut or bolt head across the wood, so it won't crush into the timber as you tighten.

02

Square edges hold steady

The square shape resists turning as the nut is tightened and sits neatly against beams, posts and sill plates.

03

Hot-dip galvanized

A thick zinc coating (ASTM A153 / F2329) protects the washer outdoors, in treated lumber and around salt water.

04

Curved for round posts

The curved 2-1/4" washer seats against round posts and piles, where a flat plate would rock.

How to choose

Four quick checks

1

Bolt size

Match the washer to your bolt diameter. The hole is 1/16" over the bolt: 9/16" for 1/2", 11/16" for 5/8", 13/16" for 3/4", 1-1/16" for 1".

2

Plate size

Go bigger for soft or wet wood and heavier loads. 2" x 2" suits decks and general framing. 4" x 4" and 6" x 6" are for heavy timber and anchor bolts.

3

Thickness

A thicker plate stays flat under high torque. Pick 3/8" or 1/2" thick for big plates and large bolts.

4

Shape

Flat for beams and sill plates. Curved for round posts and piles.

Uncle Nutty, The Nutty Company mascot
Uncle Nutty's tip: Treated lumber is hard on plain steel. Use hot-dip galvanized washers, bolts and nuts together, and check the nuts again once the wood dries and shrinks.
Where they're used

Docks, framing and foundations

Use a square plate washer wherever a bolt or nut bears on wood that's outdoors or under heavy load.

Curved galvanized square washer for round posts
  • Docks, piers and floating dock frames
  • Timber framing and post-and-beam
  • Anchor bolts and sill plates
  • Pole barns and sheds
  • Decks, pergolas and boardwalks
  • Retaining walls and landscape timbers
Square plate vs. round washers

Which washer is right for the job?

Square plate washerDock washerUSS flat washer
ShapeFlat square plateLarge roundRound
Bearing surfaceLargest, up to 6" x 6"LargeSmall
Best forHeavy timber, sill plates, anchor boltsDock and pier framingGeneral wood and steel work
ShopSquare washersGalv dock washersGalv USS washers
Every size we sell

Galvanized square washer size chart

Hot-dip galvanized. Nominal dimensions in inches, before galvanizing. Weights are approximate.

Square washer drawing: A hole diameter, B square size, C thickness
BoltHole (A)Size (B x B)Thickness (C)Approx. lb / 100SKU
1/2"9/16"2" x 2"1/8" (0.125")13GSW12218Shop
1/2"9/16"2" x 2"3/16" (0.188")20GSW122316Shop
1/2"9/16"3" x 3"1/4" (0.250")62GSW12314Shop
5/8"11/16"2" x 2"1/8" (0.125")13GSW58218Shop
5/8"11/16"2" x 2"3/16" (0.188")19GSW582316Shop
5/8"11/16"2-1/4" x 2-1/4"3/16" (0.188")25GSW58214Shop
5/8"11/16"2-1/4" x 2-1/4" curved3/16" (0.188")25GSW58214CShop
5/8"11/16"3" x 3"1/4" (0.250")61GSW58314Shop
5/8"11/16"4" x 4"3/8" (0.375")166GSW58438Shop
3/4"13/16"2-3/4" x 2-3/4"5/16" (0.312")62GSW34234516Shop
3/4"13/16"4" x 4"3/8" (0.375")165GSW34438Shop
3/4"13/16"4" x 4"1/2" (0.500")220GSW34412Shop
3/4"13/16"6" x 6"1/2" (0.500")503GSW34612Shop
1"1-1/16"4" x 4"1/2" (0.500")214GSW1412Shop
1"1-1/16"6" x 6"1/2" (0.500")498GSW1612Shop

Download the data sheet (PDF)

You'll also need

Bolts and nuts to match

FAQ

Galvanized square washer questions

What hole size goes with my bolt?

The hole is 1/16" larger than the bolt: 9/16" for a 1/2" bolt, 11/16" for 5/8", 13/16" for 3/4" and 1-1/16" for 1".

Which plate size do I need?

Follow your plans or code first. As a rule of thumb, the softer the wood and the heavier the load, the bigger the plate. Anchor bolts in sill plates and heavy dock framing usually call for 3" x 3" or larger.

What is the curved washer for?

The curved 5/8" x 2-1/4" washer is shaped to sit flat against round posts and piles, so the nut bears evenly instead of rocking on a flat plate.

Can I use these with pressure-treated lumber?

Yes. Hot-dip galvanized washers are made for treated lumber and outdoor use. Pair them with hot-dip galvanized bolts and nuts so the whole joint has the same protection.

Can you make a size you don't list?

Yes. We make custom square washers to your size, thickness, hole and finish.

Do you offer volume pricing?

Yes. Quantity discounts are applied automatically in the cart, up to 25% off on larger quantities. Orders over $100 ship free (except where noted).

Uncle Nutty waving

Need a size, thickness or quantity you don't see?

Call 203.877.1709 or email sales@nutty.com. We also make custom square washers. Purchase orders are accepted from government agencies, schools, hospitals, municipalities and companies with established credit.

Shop galvanized square washers

*Free shipping on orders over $100, except where noted.