Flush heads. Built for the dock.

Hot-dip galvanized timber bolts with a wide dome head, plus fins and rings that bite into the wood. 1/2", 5/8" and 3/4" diameters, 6" to 26" long.

Shop galvanized timber boltsSize chart ↓
★Fastener specialists since 1977
✓Order by noon EST, ships same day
$Free shipping over $100*
%Volume discounts up to 25%

Galvanized Timber Bolts

Shop by size

3 diameters, 20 lengths

Pick the diameter, then the length.

Hot-dip galvanized timber bolt with dome head, fins and rings, The Nutty Company
Why timber bolts

Made for wood that lives outdoors

01

Dome head replaces a washer

The wide, round head spreads the load over the wood, so you don't need a separate washer under the head.

02

Fins and rings bite in

Fins under the head grip the wood so the bolt doesn't spin while you tighten the nut. Rings spaced 1/4" apart seat into the wood and help keep water out of the bolt hole.

03

Low, snag-free profile

The low dome sits close to the surface, which is safer on docks, boardwalks and playgrounds where people walk or brush past.

04

Hot-dip galvanized

A thick zinc coating protects the bolt outdoors, in wet locations and around salt water.

How to install

Four steps, one wrench

1

Drill

Drill straight through both timbers. Use a bit the same size as the bolt, or 1/16" larger in wet or hard timber.

2

Drive

Tap the bolt through with a hammer until the fins and rings seat and the head sits flush with the wood.

3

Washer + nut

On the far side, add a galvanized dock, ogee or USS washer and a galvanized hex nut.

4

Tighten

Tighten the nut with a wrench. The fins keep the head from turning. Check the nuts again after the timbers dry out.

Uncle Nutty, The Nutty Company mascot
Uncle Nutty's tip: Don't counterbore for the head. Let the rings press into the wood. That's what seals the hole and keeps water out. Need longer? Use galvanized threaded rod with nuts and washers on both ends.
Where they're used

Docks, boardwalks and timber framing

Use a timber bolt wherever wood is exposed to weather and a flush, safe head matters.

  • Docks, piers and floating dock frames
  • Boardwalks and walkways
  • Playgrounds and park structures
  • Landscape timbers and retaining walls
  • Timber guide rails and bridges
  • Any exposed outdoor timber in a wet location
Timber bolt vs. carriage bolt vs. hex bolt

Which bolt is right for the job?

Timber boltCarriage boltHex bolt
HeadWide low domeRound domeHex, sits proud
Washer under headNot neededNot neededNeeded in wood
Keeps from turningFins and ringsSquare neckHold with a wrench
Helps seal the holeYes, rings under the headNoNo
ShopTimber boltsGalv carriage boltsGalv hex bolts
Every size we sell

Galvanized timber bolt size chart

Hot-dip galvanized. Nominal dimensions in inches. ★ = most popular.

Galvanized timber bolt drawing: B head diameter, C head height, E thread length
ThreadLengthThread length (E)Head dia. (B)Head height (C)SKU
1/2-13 ★6"3"1-3/4".275"GTB12136Shop
1/2-13 ★8"6"1-3/4".275"GTB12138Shop
1/2-13 ★10"6"1-3/4".275"GTB121310Shop
1/2-13 ★12"6"1-3/4".275"GTB121312Shop
5/8-116"4"2-1/4"5/16"GTB58116Shop
5/8-11 ★8"4"2-1/4"5/16"GTB58118Shop
5/8-11 ★10"6"2-1/4"5/16"GTB581110Shop
5/8-11 ★12"6"2-1/4"5/16"GTB581112Shop
5/8-1116"6"2-1/4"5/16"GTB581116Shop
5/8-1118"6"2-1/4"5/16"GTB581118Shop
5/8-1120"6"2-1/4"5/16"GTB581120Shop
5/8-1122"6"2-1/4"5/16"GTB581122Shop
5/8-1124"6"2-1/4"5/16"GTB581124Shop
5/8-1126"6"2-1/4"5/16"GTB581126Shop
3/4-1012"6"2-5/8"7/16"GTB341012Shop
3/4-1016"6"2-5/8"7/16"GTB341016Shop
3/4-1018"6"2-5/8"7/16"GTB341018Shop
3/4-1020"6"2-5/8"7/16"GTB341020Shop
3/4-1022"6"2-5/8"7/16"GTB341022Shop
3/4-1024"6"2-5/8"7/16"GTB341024Shop
You'll also need

Nuts and washers for the other side

FAQ

Galvanized timber bolt questions

Which diameter do I need?

Follow your plans or engineer first. As a rule of thumb, 1/2" suits boardwalks, playgrounds and landscape timbers, 5/8" is the most common for docks and piers, and 3/4" is for heavy timber, bridges and marine structures.

How long should the bolt be?

Add up the thickness of the timbers you are joining, then add the washer and nut plus about 1/2" so a few threads show past the nut. Then pick the next length up.

What size hole do I drill?

The same size as the bolt diameter, or 1/16" larger in wet or hard timber, so the bolt can be driven through without splitting the wood.

Do I need a washer under the head?

No. The wide dome head does the job of a washer. Use a washer under the nut on the other side.

What nut and washer go with a timber bolt?

A galvanized hex nut in the same thread (1/2-13, 5/8-11 or 3/4-10) with a galvanized dock, ogee or USS washer under it.

Do you offer volume pricing?

Yes. Quantity discounts are applied automatically in the cart, up to 25% off on larger quantities. Orders over $100 ship free (except where noted).

Uncle Nutty waving

Need a size, length or quantity you don't see?

Call 203.877.1709 or email sales@nutty.com. Purchase orders are accepted from government agencies, schools, hospitals, municipalities and companies with established credit.

Shop galvanized timber bolts

*Free shipping on orders over $100, except where noted.